PAConsult
Our standards auditor
Our standards inspector shows you the full spectrum: We test most procedures directly in-house - and we will find the right solution for you for all other requirements.
367 results found
ABD0100
AIRBUS Equipment - Design - General Requirements for Suppliers
This standard specifies the general design requirements for equipment supplied by vendors to Airbus. It includes technical specifications, quality requirements, and process guidelines to ensure the compatibility and reliability of the delivered products.
ADR
European Agreement concerning the International Carriage of Dangerous Goods by Road
This agreement governs the transport of dangerous goods by road within Europe. It defines classifications, packaging regulations, labeling requirements, and safety measures for the transport of various classes of dangerous goods.
AECTP-200
AECTP 200 Environmental Conditions
This standard describes the environmental conditions that military equipment may be exposed to during its deployment. It covers factors such as temperature, humidity, solar radiation, and other climatic influences.
AECTP-230
Climatic conditions
This standard specifies the climatic conditions under which military equipment must be tested. It defines temperature ranges, air pressure conditions, and other climatic parameters for various deployment scenarios.
AECTP-300
Climatic Environmental Testing
This standard describes the procedures for climatic environmental testing of military equipment. It covers tests for resistance to temperature changes, humidity, solar radiation, and other climatic influences.
AECTP-400
Mechanical Environmental Tests
This standard describes the procedures for mechanical environmental testing of military equipment. It covers testing for resistance to vibration, shock, impact, and other mechanical stresses.
AECTP-400-3
Mechanical Environmental Tests
Supplementary specifications for mechanical environmental tests, which define additional test procedures and requirements for specific use cases.
AERO_TN 524 5071
A350XWB Vibrational Requirements for Equipment to Cover Sustainable Engine Imbalance - Windmilling Blade Loss Condition
This technical guideline specifies the vibration requirements for equipment on board the Airbus A350XWB under conditions such as engine unbalance or blade loss. It defines limits and test procedures to ensure structural integrity.
Airbus Company Directive ABD0100 g2-0.0
Equipment - Design - General Requirements for Suppliers
Airbus Directive for Supplier Design Requirements. It covers technical specifications, quality standards, and process requirements for the supply of equipment to Airbus.
ASTM B117
Standard Practice for the Operation of Salt Spray (Fog) Apparatus
This standard describes the practice for operating salt spray cabinets for testing the corrosion resistance of materials. It defines test parameters such as salt concentration, temperature, and spray duration.
ASTM D 624
Standard Test Method for Tensile Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
This Standard specifies the method for determining the tensile strength of conventionally vulcanized rubber and thermoplastic elastomers. It is used to evaluate the mechanical properties of rubber materials.
ASTM D3078
Standard Test Method for Determining Leaks in Flexible Packaging by Bubble Emission
This method is used to detect leaks in flexible packaging by observing bubble formation. The packaging is immersed in a liquid or subjected to pressure, making any leaks visible through escaping bubbles. This test is important for packaging quality assurance, particularly in the food and pharmaceutical industries, where product contamination due to leaks must be avoided. The method is simple and inexpensive to perform, yet provides reliable leak detection.
ASTM D3103
Standard Test Method for Thermal Insulation Performance of Distribution Packages
This standard describes the test method for evaluating the thermal insulation performance of packaging, particularly for the transport of temperature-sensitive goods. The test simulates conditions during transport and measures the packaging's ability to maintain the temperature within a specified range. This is crucial for quality assurance in the packaging of food, pharmaceutical products, and other temperature-sensitive goods. The method includes measuring temperature changes under controlled conditions and evaluating the insulation performance.
ASTM D3330/D3330M
Standard Test Method for Peel Adhesion of Pressure-Sensitive Tapes
This standard describes the test method for determining the peel adhesion of pressure-sensitive adhesive tapes. The test measures the force required to peel the adhesive tape from a substrate. This is important for evaluating the adhesive properties and durability of adhesive tapes in various applications, such as packaging, construction, and the automotive industry. The test is typically performed using a tensile testing machine, where the adhesive tape is peeled from the substrate at a defined angle. The results help in selecting suitable adhesive tapes for specific applications and in quality assurance during production.
ASTM D3654-D3654M
Standard Test Methods for Shear Adhesion of Pressure-Sensitive Tapes
This standard describes the test method for determining the shear adhesion of pressure-sensitive adhesive tapes. The test measures the time a tape can withstand a defined load and temperature before failing. This is important for evaluating the long-term stability and durability of adhesive tapes in various applications, such as packaging, construction, and the automotive industry. The test is typically performed with a shear testing machine, where the adhesive tape is subjected to a defined load and temperature. The results aid in selecting suitable adhesive tapes for specific applications and in quality assurance during production.
ASTM D4169
Standard Practice for Performance Testing of Shipping Containers and Systems
This standard describes test methods for evaluating the performance of shipping containers and systems under various transport conditions. The tests include simulations of shocks, vibrations, drop tests, and other stresses that packaging is exposed to during transport. This is crucial for quality assurance and the optimization of packaging solutions, especially for the transport of sensitive goods. The method helps in selecting suitable packaging and improving transport safety.
ASTM D4321
Standard test method for the yield of plastic films
This standard describes the test method for determining the yield of plastic films. Yield is a measure of the efficiency of film production and is determined by the ratio of usable area to total area. This is important for quality assurance and optimization of production processes in the plastics industry. The method includes measuring the usable area and calculating the yield. The results help identify potential improvements in production and reduce material waste.
ASTM D4332
Standard Practice for Conditioning Containers, Packages, or Packaging Components for Test
This standard describes the procedures for conditioning containers, packages, or packaging components before conducting tests. Conditioning involves adjusting temperature, humidity, and other environmental conditions to meet test requirements. This is crucial for the accuracy and reproducibility of tests, as material properties are highly dependent on environmental conditions. The method includes defining the conditioning parameters and performing the conditioning under controlled conditions. The results help ensure the comparability of test results and support quality assurance.
ASTM D4728
Standard Test Method for Random Vibration of Shipping Containers
This standard describes the test method for simulating random vibrations that shipping containers are exposed to during transport. The test is performed using a vibration testing machine that generates random vibrations at various frequencies and amplitudes. This is important for evaluating the transport safety and durability of packaging, especially for the transport of fragile goods. The method includes defining test parameters and conducting the test under controlled conditions. The results help in selecting suitable packaging and improving transport safety.
ASTM D4991
Standard test method for leak testing empty rigid containers by vacuum method
This standard describes the test method for detecting leaks in empty rigid containers by applying a vacuum. The container is placed in a vacuum chamber, and any leaks are made visible by the ingress of air into the container. This is important for quality assurance of packaging, especially in the food and pharmaceutical industries, where product contamination due to leaks must be avoided. The method is simple and inexpensive to perform, yet provides reliable detection of leaks.
ASTM D5264
Standard practice for the abrasion resistance of printed materials by the Sutherland rub test
This standard describes the test method for determining the abrasion resistance of printed materials. The test is performed using a Sutherland rub tester, which rubs the surface of the material with a defined pressure and number of cycles. This is important for assessing the durability and quality of printed materials, especially in the packaging industry. The method includes defining the test parameters and performing the test under controlled conditions. The results help in selecting suitable materials and printing processes for specific applications and in quality assurance.
ASTM D5265
Standard Test Method for Bridge Splitting
This standard describes the test method for simulating impacts to which packaging is subjected during transport. The test is performed using a bridge impact tester, which applies a defined impact to the packaging. This is important for assessing the transport safety and durability of packaging, especially for the transport of sensitive goods. The method includes the definition of test parameters and the execution of the test under controlled conditions. The results help in selecting suitable packaging and improving transport safety.
ASTM D5276
Standard Test Method for Drop Test of Loaded Packages by Free Fall
This standard describes the test method for simulating drop impacts that loaded containers are exposed to during transport. The test is performed by dropping the container from a defined height onto a hard surface. This is important for assessing the transport safety and durability of packaging, especially for the transport of sensitive goods. The method includes defining test parameters and conducting the test under controlled conditions. The results help in selecting appropriate packaging and improving transport safety.
ASTM D6055
Standard Test Methods for Mechanical Handling of Unit Loads and Large Shipping Containers and Crates
This standard defines the test methods for the mechanical handling of unit loads and large shipping containers. It includes tests to verify the stability, strength, and handleability of packaging under various mechanical stresses. The standard is relevant for the logistics and transportation of heavy and bulky goods.
ASTM D6179
Standard Test Methods for Gross Handling of Unit Loads and Large Shipping Containers and Crates
This standard describes the test methods for the rough handling of unit loads and large shipping containers. It includes tests to verify the resistance of packaging to rough handling, as may occur during the loading and unloading of transport equipment. The standard is important for the safety and integrity of packaging during transport.
ASTM D624
Standard Test Method for Tensile Properties of Vulcanized Rubber and Thermoplastic Elastomers
This standard describes the test method for determining the tensile strength of vulcanized rubber and thermoplastic elastomers. It is crucial for evaluating material quality and durability in applications subject to high mechanical stress. The test is typically performed using a tensile testing machine, where the sample is stretched until it breaks. The results aid in selecting suitable materials for specific applications and in quality assurance during production.
ASTM D6287
Standard practice for cutting film and sheet test specimens
This standard describes the practice for cutting film and sheet test specimens. It specifies how specimens must be prepared for further testing to ensure uniform and reproducible results. The standard is important for quality assurance in the packaging industry.
ASTM D6344
Standard Test Method for Concentrated Impacts on Transport Packages
This standard describes the test method for concentrated impacts on transport packages. It is used to test the resistance of packaging to point loads. The test simulates the conditions to which packaging is exposed during handling and transportation.
ASTM D638
Standard test methods for the tensile properties of plastics
This standard describes the procedure for determining the tensile strength of plastics. It is used to evaluate the mechanical properties of plastic materials and is relevant to the plastics industry as well as the packaging sector.
ASTM D642
Standard Test Method for the Determination of the Compressive Strength of Shipping Containers, Components, and Unit Loads
This standard describes the test method for determining the compression strength of shipping containers, components, and unit loads. It serves to test the resistance of packaging to compressive loads. The test is important for the safety and integrity of packaging during transport and storage.
ASTM D6653 / D6653M
Standard Test Methods for Determining the Effects of High Altitude on Packaging Systems by Vacuum Method
This standard describes test methods for determining the effects of high altitude on packaging systems using the vacuum method. It serves to test the resistance of packaging to pressure changes that can occur during air freight. The test is important for the safety and integrity of packaging during transport.
ASTM D6988
Standard Guide for Determining the Thickness of Plastic Film Test Specimens
This standard describes the guide for determining the thickness of plastic film test specimens. It specifies how the thickness of films must be measured to ensure consistent and reproducible results. The standard is important for quality assurance in the packaging industry.
ASTM D7386
Standard Practice for Performance Testing of Packages for Single-Package Shipments
This standard describes the practice for performance testing of single-package shipments. It is intended to test the resilience of packages against the conditions they are exposed to during delivery. The test is important for the safety and integrity of packages during transport.
ASTM D880
Standard Test Method for Impact Testing of Shipping Containers and Systems
This standard describes the test method for checking the impact resistance of shipping containers. It defines test procedures and requirements to ensure the protective function of packaging during transport.
ASTM D882
Standard Test Method for Tensile Properties of Thin Plastic Sheeting
This standard describes the test method for the tensile strength of thin plastic films. It is used to test the mechanical properties of films. The test is important for quality assurance in the packaging industry.
ASTM D996
Standard Terminology for Packaging and Distribution Environments
This standard defines the standard terminology for packaging and distribution environments. It serves as a common linguistic basis for professionals in the packaging industry and includes terms related to materials, processes, and environmental conditions.
ASTM D999
Standard Test Methods for Vibration Testing of Shipping Containers
This standard describes test methods for vibration resistance testing of shipping containers. It defines test procedures and requirements to ensure the protective function of packaging during transport.
ASTM E171 / E171M
Standard Practice for Conditioning and Testing Flexible Barrier Packaging
This standard practice describes procedures for conditioning and testing flexible barrier packaging. It ensures that the packaging provides the required protection and performance characteristics.
ASTM E4
Standard Practice for Force Calibration and Verification of Testing Machines
This standard specifies procedures for the calibration and verification of force measurement in testing machines. It ensures that the measurement results from testing machines are reliable and reproducible, which is crucial for quality assurance in various industries.
ASTM E691
Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
This standard describes how interlaboratory studies should be conducted to determine the precision of test methods. It helps to ensure the reliability and comparability of test results between different laboratories.
ASTM F1140/F1140M
Standard test methods for the resistance to internal pressure failure of unlimited packages
This standard specifies the procedure for carrying out pressure tests on ungasketed packaging. It is used to assess the resistance of packaging to internal overpressure.
ASTM F1306
Standard Test Method for Resistance of Flexible Barrier Films and Laminates to Slow Puncture Rate
This standard specifies the method for determining the resistance of flexible barrier films and laminates to slow penetration. It serves to assess the protective function of packaging against external influences and is relevant to the packaging industry.
ASTM F1886/F1886M
Standard Test Procedure for Determining the Seal Integrity of Flexible Packaging by Visual Inspection
This standard describes the procedure for determining the leak-tightness of seals in flexible packaging by visual inspection. It is used to assess the quality and reliability of packaging closures and is relevant to the packaging industry.
ASTM F1929
Standard Test Method for Detection of Seal Leaks in Porous Medical Packaging by Dye Penetration
This standard describes a method for detecting leaks in seals of porous medical packaging using dye penetration. It is crucial for the safety and sterility of medical products.
ASTM F1980
Accelerated Aging Standard Guide for Sterile Barrier Systems for Medical Devices
This standard provides guidance for the accelerated aging of sterile barrier systems for medical devices. It helps to evaluate the long-term stability and safety of packaging.
ASTM F2096
Standard test method for the detection of gross leaks in packaging by internal pressurization failure (bubble test)
This standard describes a method for detecting gross leaks in packaging through internal overpressure failure, also known as the bubble test. It is important for packaging quality assurance.
ASTM F2097
Standard Guide for the Design and Evaluation of Primary Flexible Medical Device Packaging
This standard provides guidance for the design and evaluation of primary flexible packaging for medical products. It ensures that the packaging meets safety and protection requirements.
ASTM F2251
Standard Test Method for Thickness Measurement of Flexible Packaging Materials
This standard describes a method for measuring the thickness of flexible packaging materials. It is important for quality assurance and compliance with specifications.
ASTM F2252/F2252M
Standard practice for testing the adhesion of inks or coatings on flexible packaging materials using tape
This standard describes a method for evaluating the adhesive strength of inks or coatings on flexible packaging materials using adhesive tape. It is important for the quality assurance of printed or coated packaging.
ASTM F2459
Standard Test Method for Extracting and Gravimetrically Quantifying Residues from Metallic Medical Devices
This standard describes the procedure for extracting residues from metallic medical components and their quantitative determination using gravimetric analysis. It is used to assess the purity and quality of medical implants and is relevant to the medical technology industry.
ASTM F2825
Standard Practice for Climatic Conditioning of Packaging Systems for Single Parcel Shipping
This standard describes methods for the climatic stressing of packaging systems for single parcel shipping. It helps to assess the resistance of packaging under various climatic conditions.
ASTM F3039
Standard Test Method for Detection of Leaks in Non-porous Packaging or Flexible Barrier Materials by Dye Penetration
This standard describes a method for detecting leaks in non-porous packaging or flexible barrier materials using dye penetration. It is important for the safety and sterility of medical products.
ASTM F623
Standard Specification for Foley Catheters
This standard specifies the performance requirements and specifications for Foley catheters. It ensures that the catheters meet medical requirements and can be used safely.
ASTM F640
Standard Test Methods for Determining Radiopacity of Materials for Medical Use
This standard describes test methods for determining the radiopacity of medical products. It is important for the visibility of implants and other medical devices in X-ray images.
ASTM F88/F88M
Standard Test Method for Seal Strength of Flexible Barrier Materials
This standard describes the test method for determining the seal strength of flexible barrier materials used in medical and packaging applications. It specifies the procedure for creating seal seams and testing them for tensile strength to ensure the integrity of the packaging.
ASTM F904
Standard practice for delaminating plies for bond strength of laminated flexible materials
This standard describes the method for separating the plies of laminated flexible materials to determine bond strength. It is important for evaluating the adhesion between layers in composite materials, especially in packaging applications.
ATA Spec 300:
Airline amenity kit packaging specification
This specification sets forth the requirements for packaging aviation industry accessories. It includes guidelines for materials, constructions, and testing to ensure the safety and efficiency of packaging during transport.
Construction Regulations (BV) for the German Navy - Navy - 043/E
Construction Regulations for German Navy Ships - Navy 043/E Design Features for Shock-Resistant Construction (Supplement to BV Booklet 043 Impacts, Shock Absorption, Shock Safety).
This building regulation specifies the construction features for shock-resistant construction of German Navy ships. It includes requirements for structure and damping systems to protect the ships against impacts and shock loads.
Construction Regulation (BV) for the German Armed Forces Ships 0430
Building regulations for the German Navy 0430 Shock resistance. Experimental and computational proof for surface ships and submarines.
This building regulation describes the requirements for the shock safety of surface vessels and submarines of the German armed forces. It specifies how experimental and computational evidence for shock resistance is to be provided.
BMW GS 95006-7-1
Wiring harnesses in motor vehicles, tests
This standard specifies the test procedures for wiring harnesses in motor vehicles. It includes requirements for electrical and mechanical properties as well as tests to ensure reliability and safety.
BMW GS 95024-3-1
Electrical and Electronic Components in Motor Vehicles, Environmental Requirements and Testing
This standard describes the environmental requirements and test procedures for electrical and electronic components in motor vehicles. It includes tests for resistance to temperature, humidity, and mechanical stresses.
Boeing D6-36440 Volume 1 Rev G
Standard Cabin System Requirements Document, Volume 1
This document sets the requirements for aircraft cabin systems. It includes specifications for the design, safety, and functionality of cabin furnishings.
Boeing D6-81926 REV K
Boeing proprietary CAGE Code 81205. Equipment vibration test requirements
This specification defines the requirements for vibration testing of aircraft equipment. It includes procedures for simulating and measuring vibrations to ensure equipment reliability.
Boeing D6-85182-Rev. B
General Electric Qualification Test Procedure, Seats Integration Team – Seats Electrics Tech Center
This test procedure describes the qualification tests for electrical systems in aircraft seats. It includes tests for the functionality, safety, and reliability of the electrical components.
BS 6196
Specification for sterile single-use epidural catheters and introducer needles
This standard specifies requirements for sterile epidural catheters and introducer needles. It includes specifications for materials, design, and sterility to ensure safety in medical applications.
BS EN 1174-1
Sterilization of medical devices - Estimation of the population of microorganisms on a product - Part 1: Requirements
This standard describes methods for estimating the microbial contamination (bioburden) on a medical device prior to sterilization. This value is crucial for the establishment and validation of a sterilization process.
BS EN 12390-5
Testing of hardened concrete - Part 5: Flexural tensile strength of test specimens
This standard specifies a method for determining the flexural tensile strength of concrete specimens. It is an essential component of quality control and the design of concrete components.
BS EN 13726
Test procedures for wound dressings. Aspects of absorption behavior, moisture penetration, waterproofness, and adaptability
This standard specifies test methods for evaluating the absorption properties of primary wound dressings, such as their capacity and ability to retain fluid under pressure.
BS EN 1441
Medical Device Risk Analysis
This standard (now replaced by ISO 14971) described a systematic process for identifying, analyzing, and evaluating risks associated with the use of medical devices.
BS EN 556-1
Sterilization of medical devices - Requirements for medical devices labelled "STERILE" - Part 1: Requirements for medical devices sterilized in the sterile packaging
This fundamental standard establishes the requirement that a product may only be labeled as sterile if the theoretical probability of finding a viable microorganism is less than or equal to 1 in 1 million.
BS EN 60068-1
Environmental Testing Part 1: General and Guidance (IEC 60068-1)
This fundamental part of the DIN EN 60068 series of standards provides an introduction and guide to the various environmental tests (climatic, mechanical), their purpose, and their correct application.
BS EN 61822
Electrical installations for airfield lighting and beacons
This standard describes the requirements for electrical installations for airport lighting and marking. It includes specifications for current regulators and other components to ensure the safety and functionality of the lighting systems.
BS EN 868-5
Packaging for terminally sterilized medical devices – Part 5: Sealable pouches and bags made from porous materials and plastic film combinations – Requirements and test methods
This part of the standards series specifies the requirements and test methods for sealable bags and pouches consisting of a porous and a transparent plastic side, intended for the sterilization of medical devices.
BS EN ISO 10993-1
Biological evaluation of medical devices - Part 1: Evaluation and testing within a risk management system (ISO/DIS 10993-1)
This central standard describes the general framework for the biological evaluation of medical devices. It specifies how potential biological risks must be identified and evaluated through testing.
BS EN ISO 10993-5
Biological evaluation of medical devices - Part 5: Tests for in vitro cytotoxicity (ISO 10993-5)
This standard describes test methods for assessing the cytotoxic potential of medical devices and their materials. It examines whether extracts of the material inhibit or damage the growth of cell cultures in the laboratory.
BS EN ISO 11135-1
Sterilization of health care products — Ethylene oxide — Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices (ISO 11135-1)
This standard specifies requirements for the sterilization of medical devices using ethylene oxide (EO). It describes the entire process from development through validation to routine monitoring.
BS EN ISO 11138-1
Sterilization of health care products - Biological indicators - Part 1: General requirements (ISO 11138-1)
This standard specifies general requirements for the manufacture, performance, and labeling of biological indicators used to monitor the efficacy of sterilization processes.
BS EN ISO 11607-1
Packaging for terminally sterilized medical devices - Part 1: Requirements for materials, sterile barrier systems and packaging systems (ISO 11607-1)
This central norm for medical packaging specifies the general requirements for materials and systems that must ensure the sterility of a medical device from the point of sterilization to the point of use.
BS EN ISO 11607-2
Packaging for terminally sterilized medical devices - Part 2: Validation requirements for forming, sealing and assembly processes (ISO 11607-2)
This part of the standard specifies the requirements for the validation of packaging processes (e.g., sealing, forming) to ensure that sterile barrier systems are manufactured consistently and reliably.
BS EN ISO 11737-1
Sterilization of health care products - Microbiological methods - Part 1: Determination of microbial population on products (ISO 11737-1)
This standard specifies methods for determining the number and type of microorganisms (bioburden) on a medical device prior to sterilization. This information is essential for the validation of the sterilization process.
BS EN ISO 14971
Medical Devices - Application of Risk Management to Medical Devices (ISO14971)
This is the central standard for the risk management of medical devices. It describes a systematic process for identifying hazards, estimating and evaluating risks, and controlling them throughout the entire product lifecycle.
BS EN ISO 15223-1
Medical devices - Symbols to be used with medical device labels, labelling and information to be supplied - Part 1: General requirements (ISO 15223-1)
This standard establishes the internationally recognized symbols used on medical devices and their packaging to efficiently and language-independently convey information such as "sterile," "single-use," or "date of manufacture.".
BS EN ISO 20417
Medical devices — Requirements for information provided by the manufacturer (ISO/DIS 20417)
This standard specifies the general requirements for the information that a manufacturer must provide with a medical device. This includes labeling, instructions for use, and technical descriptions.
BS IEC 60092-504: 2001
Electrical installations on ships — Part 504: Special features — Control and instrumentation
This standard defines the requirements for electrical installations on ships, particularly for control and instrumentation. It includes specifications for the design, installation, and testing of the systems.
BS ISO 7864
Sterile hypodermic needles for single use — Requirements and test methods (ISO/DIS 7864)
This standard sets out the requirements for sterile single-use injection needles. It covers aspects such as materials, dimensions, cleanliness, tip sharpness, and sterility to ensure safe and effective use for patients.
BS ISO 80369-1
Small-bore connectors for liquids and gases in
This is the foundational part of an important series of standards developed to prevent misconnections between different medical systems (e.g., enteral nutrition and intravenous access) and thereby increase patient safety.
BS ISO 80369-7
Connectors for small-bore applications in medical and healthcare applications - Part 7: Connectors for intravascular or hypodermic applications (ISO80369-7)
This specific part of the standards series standardizes the widely used Luer connectors. It ensures these connectors are compatible and cannot be accidentally connected to other systems.
BS ISO 8537
Sterile single-use insulin syringes with or without needle (ISO/DIS 8537)
This standard defines the specific requirements for insulin syringes to ensure accurate and safe dosage. It includes criteria for scaling, dosage accuracy, and compatibility with insulin needles.
BS ISO 9626
Stainless steel needle tubing for the manufacture of medical devices - Requirements and test methods (ISO/DIS 9626)
This standard specifies the requirements for raw materials (stainless steel tubes) used in the manufacture of medical cannulas. It covers material properties, dimensions, surface finish, and mechanical strength.
Bureau Veritas NR467 C DT R19
Rules for the Classification of Steel Ships - NR467 - Part C - Machinery, Electrical, Automation and Fire Protection
These classification rules describe the requirements for machinery, electrical systems, automation, and fire protection in steel ships. They include specifications for the design, installation, and testing of the systems.
BV 0240 Vibration resistance
Construction regulations for German Navy ships 0240 Vibration resistance
This building regulation specifies the requirements for the vibration safety of German Navy ships. It includes specifications for the design, installation, and testing of vibration damping systems.
DEF STAN 00-035 Part 03
Defence Standard 00-035 Part 03 - Environmental Handbook for Defence Materiel - Part 03: Environmental Test Methods
This standard specifies environmental test methods for defense materiel to assess the resistance of military equipment to various environmental conditions. It includes tests such as temperature changes, humidity, salt spray, and vibration to ensure reliability under extreme conditions.
DEF STAN 00-035 Part 4
Defence Standard 00-035 - Environmental Handbook for Defence Materiel - Part 4 - Natural Environments
This standard describes the natural environmental conditions that must be considered in the design of military material. It includes factors such as climate, temperature, humidity, and environmental stresses to ensure that equipment functions under realistic operating conditions.
DEF(AUST)5168
Australian Government / Australian Defence Standard / DEF(AUST)5168: Climatic and Environmental Conditions Affecting the Design of Military Materiel
This Australian Standard defines the climatic and environmental conditions that must be considered during the development of military materiel. It serves as a guide for engineers and designers to ensure that equipment meets the requirements in various climatic zones.
DIN 13097-4
Medical Needles - Part 4: Bevel Types, Requirements, and Testing
This standard specifies the requirements for medical cannulas, in particular their tip geometries and test methods. It defines how the sharpness and quality of cannulas are to be evaluated to ensure that they meet medical requirements.
DIN 1311-1
Oscillations: Oscillating Systems, Concepts, Classification.
This standard defines terms and the classification of vibratory systems. It serves as a basis for the description and analysis of oscillations in technical systems.
DIN 1311-3
Oscillations. Part 3: Linear, time-invariant oscillating systems with a finite number of degrees of freedom.
This standard deals with linear, time-invariant, oscillatory systems with a finite number of degrees of freedom. It defines methods for the analysis and calculation of such systems.
DIN 1313
Size Design
This standard deals with the fundamentals of dimensioning, particularly in technical applications. It serves as a guide for establishing and using dimensions in engineering.
DIN 30786-2
Transport Loads - Data Collection of Mechanical-Dynamic Loads. Part 2: Value Collections
This standard collects data on mechanical-dynamic loads during transport. It serves as a reference for the assessment and simulation of transport loads to ensure the safety and reliability of transported goods.
DIN 53 387
Testing of plastics and elastomers. Weathering in equipment. Stress by filtered xenon arc radiation and periodic wetting.
This standard specifies test methods for the weathering of plastics and elastomers. It describes how materials are subjected to filtered xenon arc radiation and periodic wetting to evaluate their resistance to aging.
DIN 53504
Testing of Rubber and Elastomers - Determination of Tensile Strength, Tensile Strength, Elongation at Break and Stress Values in Tensile Test
This standard describes test methods for determining the mechanical properties of rubber and elastomers, particularly tensile strength, tear strength, elongation at break, and stress values in the tensile test. It is used for quality assurance and material characterization.
DIN 55440-1
Packaging Material Testing - Determination of Compressive Strength - Part 1: Test at Constant Feed Rate
This standard specifies a method for determining the compression resistance of packaging. It describes how resistance to compression loads is measured at a constant feed rate in order to assess the stability of packaging.
DIN 55543-1
Packaging testing - Test methods for packaging films Part 1: Determination of film thickness
This standard describes the test method for determining the thickness of packaging films. It is used for quality assurance and for compliance with specifications for packaging materials.
DIN 58953-6
Sterilization – Sterilized Goods Supply Part 6: Testing the Microbial Barrier Properties of Packaging Materials for Medical Devices to Be Sterilized
This standard specifies test methods for verifying the microbial barrier properties of packaging materials for sterilized medical devices. It ensures that the packaging remains a microbial barrier during the sterilization process and subsequent storage.
DIN CEN ISO TS 16775
Packaging for terminally sterilized medical devices – Guidance on the application of ISO 11607-1 and ISO 11607-2
This standard provides guidance on the application of ISO Standards 11607-1 and 11607-2 for sterile medical device packaging. It assists in the selection and testing of suitable packaging materials.
DIN EN (IEC) 60068-2-1
Environmental Tests Part 2-1: Test Procedures - Test A: Cold
This standard specifies the test procedure for the cold test (Test A), in which products are exposed to extreme cold temperatures to assess their performance and reliability under such conditions.
DIN EN (IEC) 60068-2-11
Environmental Influences - Part 2-11: Test Procedures - Test Ka: Salt Spray
This procedure is used to assess the corrosion resistance of products, especially those with metallic surfaces and protective coatings, under the influence of a constant, aggressive salt mist atmosphere.
DIN EN (IEC) 60068-2-13
Environmental tests Part 2-13: Tests - Test group M: Low air pressure
This standard describes the test procedure for evaluating product performance under low air pressure conditions. It is relevant for products used at high altitudes or under vacuum conditions.
DIN EN (IEC) 60068-2-14
Environmental Tests Part 2-14: Tests - Test N: Temperature Cycling
This standard specifies the test procedure for the temperature cycling test (test N), in which products are subjected to repeated cycles of high and low temperatures to evaluate their resistance to thermal stress.
DIN EN (IEC) 60068-2-17
Environmental tests - Part 2-17: Test procedures - Test Q: Watertightness
This standard specifies the test procedure for the leak tightness test (Q test), where products are tested for their ability to remain sealed under various conditions. This is particularly important for products used in humid or dusty environments.
DIN EN (IEC) 60068-2-2
Environmental Influences Part 2-2: Test Procedures - Test B: Dry Heat
This standard describes the test procedure for the dry heat test (Test Group B). Products are subjected to extreme temperatures to assess their resistance to thermal stress.
DIN EN (IEC) 60068-2-30
Environmental Influences - Part 2-30: Test Procedures - Test Db: Humid Heat, Cyclic (12h + 12h Cycles)
This standard specifies the test procedure for the cyclic damp heat test (Test Db), in which products are subjected to repeated cycles of dampness and heat to assess their resistance to such conditions.
DIN EN (IEC) 60068-2-38
Environmental influences - Part 2-38: Test procedures - Test Z/AD: Combined test, temperature/humidity, cyclic
This standard defines test methods for combined environmental tests in which temperature and humidity are varied cyclically. It is used to assess the long-term durability of products under changing climatic conditions.
DIN EN (IEC) 60068-2-5
Environmental influences - Part 2-5: Test procedures - Test S: Simulated terrestrial sunlight and guide to solar radiation and weathering
This standard describes test methods for the simulation of solar irradiation at ground level. It is relevant for assessing the resistance of materials and products to UV radiation and weathering.
DIN EN (IEC) 60068-2-52
Environmental influences - Part 2-52: Test procedures - Test Kb: Salt mist, cyclic
This standard defines the test methods for cyclic salt spray tests to assess the corrosion resistance of products. It is important for evaluating durability in marine or industrial environments.
DIN EN (IEC) 60068-2-78
Environmental testing - Part 2-78: Test methods - Test Cab: Damp heat, constant
This standard describes the test methods for constant damp heat tests. It is used to assess the reliability of products under humid and warm conditions.
DIN EN (IEC) 60068-3-1
Environmental influences - Part 3-1: Supporting documentation and guidance - Cold and dry heat tests
This future standard (2024) will provide supporting documentation and guidance for cold and dry heat tests. It will assist in conducting environmental tests to assess the resilience of equipment under extreme temperature conditions.
DIN EN (IEC) 60068-3-6
Environmental Influences - Part 3-6: Supporting Documentation and Guidance - Confirmation of Capability of Temperature and Climate Chambers
This standard provides guidance and supporting documentation for verifying the performance of temperature and climate chambers. It ensures that these testing devices meet accuracy and reliability requirements.
DIN EN (IEC) 60512-11-1
Connectors for electrical and electronic equipment - Tests and measurements - Part 11-1: Climatic tests - Test 11a - Damp heat, steady state
This standard defines procedures for testing electro-mechanical components under various climatic conditions such as temperature, humidity, and atmospheric pressure. It is important for assessing the reliability and performance of these components in different environments.
DIN EN (IEC) 60721-3-1
Classification of environmental conditions - Part 3-1: Classes of influencing quantities and their limit values - Storage
This standard classifies environmental conditions for the transport of equipment and components. It defines classes of environmental influencing factors such as temperature, humidity, and mechanical stresses, as well as their limit values.
DIN EN (IEC) 60721-3-2
Classification of environmental conditions Part 3: Classes of environmental influences and their limit values, Main section 2; Transport
This standard classifies environmental conditions for the transport of equipment and components. It defines classes of environmental influencing factors such as temperature, humidity, and mechanical stresses, as well as their limit values.
DIN EN (IEC) 60721-3-3
Classification of environmental conditions Part 3: Classes of environmental influences and their limit values. Main Section 3: Stationary use, protected from weather.
This standard classifies environmental conditions for the stationary use of equipment and components under protected conditions. It defines classes of environmental influence quantities such as temperature, humidity, and mechanical stresses, as well as their limit values.
DIN EN (IEC) 61298-3
Measurement, control and automation process devices - General methods and procedures for evaluating operating behaviour - Part 3: Tests for the effects of influencing quantities
This standard specifies test procedures for evaluating the effects of influencing factors such as temperature, humidity, and vibration on process measurement, control, and regulation equipment. It is part of a series of standards assessing the operational performance of this equipment under various environmental influences.
DIN EN (IEC) 61373
Railway Applications Rolling Stock of Railway Vehicles: Railway Applications, Tests for Vibration and Shock
This standard defines test procedures for assessing the resistance of railway vehicle components to vibration and shock loads. Amendment 1 updates the original standard from 2011 and takes into account new requirements for the reliability of railway applications.
DIN EN (IEC) 62759-1
Photovoltaic (PV) Modules - Transport Testing - Part 1: Transport and Shipment of PV Module Packages
This standard specifies test methods for evaluating the transportability of photovoltaic modules. It includes tests for mechanical loads, vibrations, and climatic conditions during transport to prevent damage to the modules.
DIN EN 12094-13
Components for gaseous extinguishing systems
This standard specifies requirements and test methods for components of gaseous extinguishing systems. It ensures that the components meet safety requirements and function reliably.
DIN EN 12094-4
Fixed firefighting systems - Components for gaseous extinguishing systems
This standard specifies requirements and test methods for components of fixed fire suppression systems using gaseous extinguishing agents. It ensures that the components comply with safety requirements and function reliably.
DIN EN 13018
Non-destructive testing - Visual inspection - General principles
This standard defines the fundamental principles and procedures for visual inspection as a non-destructive testing method. It includes requirements for lighting, visual conditions, personnel qualification, and the documentation of inspection results. Visual inspection is an essential method for detecting surface defects, corrosion, or other visually discernible flaws in materials and components.
DIN EN 14149
Shipping-ready packages and load units. Vertical impact test by tilting.
This standard specifies a test method for assessing the resistance of transport packages and unit loads to vertical shocks from tipping. The method simulates the stresses to which packages are exposed during transport and helps to evaluate packaging quality. The test is particularly relevant for protecting fragile goods during transport.
DIN EN 14744
Inland and sea navigation lights
This standard specifies the requirements for navigation lights for inland and maritime vessels. It includes technical specifications such as luminous intensity, color, and positioning of the lights to ensure safety in maritime traffic. The standard is crucial for the visibility of vessels and the prevention of collisions.
DIN EN 1615
Catheters and transfer devices for enteral nutrition and their single-use connectors. Design and testing
This standard defines the requirements for catheters and administration sets for enteral nutrition, as well as their connectors. It covers material requirements, design criteria, and test methods to ensure the safety and functionality of these medical devices. The standard is important for preventing infections and complications in enteral nutrition.
DIN EN 1789
Ambulance vehicles and their equipment - Ambulance
This standard specifies the requirements for ambulances and their equipment to ensure the safety and efficiency of emergency medical services. It includes requirements for vehicle construction, medical equipment, and workplace ergonomics. The standard is crucial for providing high-quality emergency care.
DIN EN 1865-1
Ambulance vehicles in ambulances - Part 1: General stretcher systems and ambulance equipment
This standard defines the requirements for stretcher systems and other patient transport devices in ambulances. It includes design criteria, safety requirements, and testing procedures to ensure patient safety and comfort during transport. The standard is important for efficient and safe patient care in emergency medical services.
DIN EN 22248
Packaging. Packing for shipment. Vertical shock test (free fall) (ISO 2248)
This standard describes a test method for evaluating the resistance of ready-for-shipment packages to vertical impacts from free fall. The method simulates stresses during transport and helps assess packaging quality. The test is particularly relevant for the protection of fragile goods.
DIN EN 2234
Aerospace - Electric cables, fire-resistant - Technical delivery conditions
This standard specifies the technical requirements for fire-resistant electrical cables for use in aerospace. It covers material requirements, fire resistance test methods, and electrical properties. The standard is crucial for safety in aircraft and spacecraft.
DIN EN 22876
Packaging. Shipping-ready packages. Overturning test (sequential) (ISO 2876)
This standard specifies a test method for evaluating the resistance of shipping-ready packages to tipping. The method simulates the stresses encountered during transport and helps to assess packaging quality. The test is particularly relevant for protecting delicate goods.
DIN EN 285
Sterilization – Steam Sterilizers – Large-Capacity Sterilizers
This standard defines the requirements for large steam sterilizers. It covers technical specifications, test methods, and sterilization performance requirements. The standard is crucial for the safety and efficiency of sterilization in healthcare facilities.
DIN EN 28768
Packaging; Transport packages; Stacking test (ISO 8768); German version EN 28768
Describes procedures for a tipping test of shipped packages.
DIN EN 455-2
Medical Gloves for Single Use - Part 2: Requirements and Test Methods for Physical Properties
This standard specifies the requirements for the physical properties of disposable medical gloves, such as dimensions and tensile strength (both before and after accelerated aging), to ensure their protective function.
DIN EN 50125-1
Railway applications - Environmental conditions for equipment - Part 1: Equipment on rolling stock; German version EN50125-1
This part of the standard defines requirements for fixed electrical installations on railway vehicles.
DIN EN 50125-2
Railway applications – Environmental conditions for equipment – Part 2: Fixed electrical installations
This standard specifies environmental conditions for fixed electrical installations in rail transport. It ensures that these installations function reliably under the specific environmental conditions of rail transport.
DIN EN 50125-3
Railway applications - Environmental conditions for rolling stock - Part 3: Environmental conditions for signalling and telecommunication equipment
This standard describes the environmental conditions for railway equipment. It covers requirements for resistance to climatic influences, mechanical stresses, and other environmental influences and is relevant for the railway industry.
DIN EN 50155
Railway applications - Rolling stock - Electronic equipment; German version EN50155
This standard specifies the requirements for electrical equipment in railway vehicles. It covers electrical, mechanical, and environmental requirements, as well as test procedures to ensure reliability and safety. The standard is important for the operation of railway vehicles.
DIN EN 54-10
Fire detection and fire alarm systems - Part 10: Flame detectors; Point type detectors; German version EN 54-10
This standard defines the requirements for fire alarm systems to ensure reliable detection and reporting of fires. It includes technical specifications, test procedures, and installation requirements. The standard is crucial for fire protection in buildings.
DIN EN 54-2
Fire Alarm Systems - Part 2: Fire Alarm Control Panels
This standard specifies the requirements for fire alarm control panels, which are the core of fire alarm systems. It includes requirements for functionality, reliability, and user-friendliness. The standard is important for efficient early fire detection and notification.
DIN EN 54-20
Fire alarm systems – Part 20: Aspirating smoke detectors
This standard defines the requirements for aspirating smoke detectors used for early fire detection. It includes technical specifications and test procedures to ensure reliability. The standard is crucial for fire protection in large buildings and industrial facilities.
DIN EN 54-3
Fire detection systems – Part 3: Fire alarm devices – Audible alarm devices
This standard specifies the requirements for acoustic signaling devices in fire alarm systems. It covers requirements for volume, frequency, and clarity of alarm signals. The standard is important for effectively warning people in the event of a fire.
DIN EN 546-2
Aluminum and aluminum alloys - Foil - Part 2: Mechanical properties; German version EN 546-2
This standard defines the mechanical properties of aluminum foils and alloys. It includes requirements for tensile strength, elongation, and other mechanical properties. The standard is important for quality assurance in the processing of aluminum foils.
DIN EN 60068-1
Environmental Influences - Part 1: General Information and Guidelines
This standard establishes the general principles for environmental testing, including definitions, test methods, and guidelines. It serves as a framework for conducting environmental tests to ensure the reliability and durability of products under various environmental influences.
DIN EN 60068-2-18
Environmental testing – Part 2-18: Tests, Test R and guidance: Water
This standard describes the test procedure for the water test (test R), in which products are exposed to extreme water influences to assess their resistance to moisture and corrosion.
DIN EN 60068-2-27
Environmental influences - Part 2-27: Test procedures - Test Ea and guide: Shock
This standard specifies the test procedure for shock testing (test Ea), where products are subjected to mechanical impacts to assess their resistance to mechanical stresses.
DIN EN 60068-2-29
Environmental testing - Part 2-29: Tests - Test Eb and guidance: Continuous shock
This standard describes the test procedure for the endurance shock test (Test Eb), in which products are subjected to repeated mechanical impacts to assess their resistance to long-term mechanical stress.
DIN EN 60068-2-31
Environmental Influences - Part 2-31: Test Procedures - Test Ec: Shocks from rough handling, primarily for devices
This standard specifies the test method for the shock test by rough handling (Test Ec), in which products are exposed to mechanical shocks that can arise from improper handling. This is particularly important for portable devices.
DIN EN 60068-2-32
Environmental testing - Part 2-32: Tests - Test Ed: Free Fall
This standard describes the test method for the free fall test (test Ed), in which products are dropped from a specific height to assess their resistance to mechanical stress. The standard has been withdrawn and is no longer valid.
DIN EN 60068-2-33
Environmental tests Part 2-33: Tests - Guidance on test group N: Temperature cycling
This standard specifies the procedures for thermal shock testing to evaluate the effects of rapid temperature fluctuations on products. It is important for assessing the reliability of devices in environments with extreme temperature changes.
DIN EN 60068-2-47
Environmental Influences – Part 2-47: Test Procedures – Mounting of Test Specimens for Vibration, Shock, and Similar Dynamic Tests
This standard provides instructions for the mounting of test specimens for vibration, shock, and similar dynamic tests. It is crucial for the correct execution of mechanical stress tests and the comparability of results.
DIN EN 60068-2-48
Environmental Testing - Part 2-48: Tests; Guidance on the application of IEC 60068 tests to simulate the effects of storage
This standard provides guidance on simulating the effects of storage on products. It helps assess the reliability and durability of equipment under storage conditions.
IEC 60068-2-55
Environmental testing Part 2-55: Tests Test Ee and guidance: Bounce
This standard defines the procedures for impact tests to evaluate the resistance of products to mechanical shocks. It is relevant for assessing the robustness of devices and components.
DIN EN 60068-2-57
Environmental test – Part 2-57: Tests – Test Ff: Vibration – Time-history and sinusoidal-burst method
This standard describes test procedures for evaluating the vibration resistance of equipment. It helps to assess the reliability and performance of equipment under vibration stress.
DIN EN 60068-2-59
Environmental tests - Part 2-59: Tests; Test Fe: Vibration, sinusoidal pulses
This standard describes the test methods for vibration tests using sine impulses. It is used to assess the mechanical load capacity of products under dynamic conditions.
DIN EN 60068-2-6
Environmental influences - Part 2-6: Test procedures - Test Fc: Vibration (sinusoidal)
This standard defines test methods for sinusoidal vibration testing. It is crucial for evaluating the mechanical endurance of products under harmonic vibrations.
DIN EN 60068-2-61
Part 2 — 61 Environmental Tests; Part 2: Test Procedures; Test Z/ABDM: Sequence of Climatic Tests.
This standard specifies the sequence and execution of climatic tests to assess the environmental resistance of products. It includes requirements for temperature, humidity, and other climatic conditions. The standard is important for the reliability of products under various environmental conditions.
IEC 60068-2-64
Environmental Influences Part 2-64 Test Procedures - Test Fh: Vibration, Broadband Noise (Digitally Controlled) and Guidelines
This standard describes the test methods for random vibration tests. It is used to assess the mechanical resilience of products under random vibrations.
DIN EN 60068-2-66
Environmental testing - Part 2-66: Tests; Test Cx: Damp heat, constant (unsaturated moist air)
This standard describes the test methods for constant damp heat tests. It is used to assess the reliability of products under humid and warm conditions.
DIN EN 60068-2-67
Environmental Influences - Part 2-67: Test Methods - Test Cy: Damp Heat, constant, accelerated testing, preferably for building components
This standard describes the test methods for accelerated damp-heat tests, particularly for construction components. It serves for the rapid assessment of reliability under humid and warm conditions.
DIN EN 60068-2-75
Environmental Influences - Part 2 - 75: Tests - Test Eh: Hammer Tests
This standard describes standardized hammer tests for determining the resistance of enclosures to mechanical impacts. The results are classified using the IK code (see also DIN EN 62262).
DIN EN 60068-2-81
Environmental testing - Part 2-81: Tests - Shock test E: Shock response spectrum synthesis
This standard defines the test methods for shock tests where the shock response spectrum is synthesized. It is used to assess the resistance of products to mechanical shock.
DIN EN 60066-507
Electrical installations on ships - Part 507: Small craft
This standard specifies the requirements and test procedures for electrical installations on yachts. It serves to ensure the safety and reliability of electrical systems in marine environments.
DIN EN 60255-21-1
Electrical Relays - Part 21: Vibration, Shock, Bump, and Earthquake Tests on Measuring Relays and Protective Devices; Main Section 1: Vibration Tests
This standard specifies test methods for electrical relays to evaluate their behavior under vibration, shock, endurance shock, and seismic conditions. It is crucial for the safety and reliability of measuring and protective equipment in electrical engineering.
DIN EN 60255-21-2
Electric Relays - Part 21: Vibration, Shock, Endurance Shock and Earthquake Tests on Measuring Relays and Protective Devices; Main Section 2: Shock and Endurance Shock Tests
This standard specifies test methods for electrical relays to evaluate their behavior under vibration, shock, endurance shock, and seismic conditions. It is crucial for the safety and reliability of measuring and protective equipment in electrical engineering.
DIN EN 60255-21-3
Electric Relays - Part 21: Vibration, Shock, Repetitive Shock, and Earthquake Tests on Miniature Relays and Protective Devices; Main Section 3: Earthquake Tests
This standard specifies test methods for electrical relays to evaluate their behavior under vibration, shock, endurance shock, and seismic conditions. It is crucial for the safety and reliability of measuring and protective equipment in electrical engineering.
DIN EN 60529
Degrees of protection by enclosures (IP Code)
This standard defines the degrees of protection provided by enclosures (IP code), which specify the level of protection against the ingress of solid foreign objects and water. It is crucial for the safety and reliability of electrical equipment in various environments.
DIN EN 60601-1
Medical electrical equipment - Part 1: General requirements for basic safety and essential performance of transport incubators
This standard specifies general safety requirements for medical electrical equipment, particularly transport incubators. It covers aspects such as electrical safety, mechanical strength, and protection against overheating, to ensure the safety of patients and users.
DIN EN 60601-2-20
Specific provisions for safety including the essential performance characteristics of transport incubators
This standard specifies special safety requirements for transport incubators that go beyond the general requirements. It covers aspects such as specific performance characteristics, protection against environmental influences, and special design requirements.
ISO 4210-2:2015 specifies requirements and test methods for brakes, frame, fork, steering, wheels, tires, pedals, cranks, chainwheels, and chain for bicycles.
Tests for Assessing Fire Hazard - Part 11-5: Test Flames - Needle Flame Test Procedure - Test Equipment, Confirmation Test Arrangements and Guidance
This standard defines test procedures using a needle flame to assess the fire hazard of materials and components. It specifies the test setup, test execution, and evaluation of results to assess fire behavior.
DIN EN 60945
General Requirements - Test Procedures and Required Test Results Navigational and Radio Communication Equipment and Systems for Maritime Navigation
This standard defines the basic requirements and test procedures for maritime navigation and radiocommunication equipment. It covers aspects such as electrical safety, mechanical strength, and environmental resistance to ensure the reliability of these systems under the harsh conditions of maritime navigation.
DIN EN 62262
Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code) (IEC 62262); German version EN 62262
This standard defines degrees of protection (IK code) for enclosures of electrical equipment against mechanical impacts such as shocks, blows, and vibrations. It helps in selecting suitable enclosures for various application areas and environments. The 2022 update takes into account new requirements for mechanical resistance.
DIN EN 868-10
Packaging for sterilizable medical devices in final packaging - Part 10: Adhesive-coated nonwoven materials made from polyolefins - Requirements and test methods
This standard specifies requirements and test methods for adhesive-coated nonwoven materials made of polyolefins, which are used for the packaging of sterilizable medical devices. It ensures that the packaging meets the requirements for sterilization and protection of the products.
DIN EN 868-4
Packaging for medical devices to be terminally sterilized - Part 4: Paper bags - Requirements and test methods
This standard defines requirements and test methods for paper bags used for the packaging of sterilizable medical devices. It ensures that the bags meet the requirements for sterilization and protection of the products.
DIN EN 868-5
Packaging for terminally sterilized medical devices – Part 5: Sealable pouches and bags made from porous materials and plastic film combinations – Requirements and test methods
This standard specifies requirements and test methods for sealable transparent pouches and bags made from porous materials and plastic composite film, which are used for the packaging of sterilizable medical devices. It ensures that the packaging meets the requirements for sterilization and product protection.
DIN EN 868-6
Packaging for terminally sterilized medical devices - Part 6: Paper for low-temperature sterilization processes - Requirements and test methods
This standard specifies requirements and test methods for paper used in low-temperature sterilization processes. It ensures that the packaging meets the requirements for sterilization and protection of medical devices.
DIN EN 868-7
Packaging for sterilized medical devices in terminal sterilization - Part 7: Adhesive coated paper for low-temperature sterilization processes - Requirements and test methods
This standard defines requirements and test procedures for adhesive-coated paper used in low-temperature sterilization processes. It ensures that the packaging meets the requirements for sterilization and protection of medical devices.
DIN EN 868-8
Packaging for medical devices to be sterilized in terminal sterilization - Part 8: Reusable sterilization containers for steam sterilizers according to EN 285 - Requirements and test methods
This standard specifies requirements and test methods for reusable sterilization containers intended for use in steam sterilizers. It ensures that the containers meet the requirements for sterilization and protection of medical devices.
DIN EN IEC 60079-0
Explosive Atmospheres - Part 0: Equipment - General Requirements
This standard defines the general requirements for equipment used in potentially explosive atmospheres. It covers safety requirements, test procedures, and marking regulations to ensure safety in such environments. The standard is part of a series of standards dealing with explosion protection technology.
DIN EN IEC 60721-2-6
Classification of environmental conditions – Part 2-6: Natural influences – Seismic influences
This standard defines the classification of environmental conditions, particularly seismic influences. It serves to assess the effects of earthquakes on technical systems and equipment. The standard helps in establishing requirements for the resistance of products to seismic loads.
DIN EN ISO 10079-1
Medical Suction Devices - Part 1: Electrically Operated Suction Devices
This standard specifies requirements and test methods for electrically driven medical suction devices. It ensures that these devices are safe and effective.
DIN EN ISO 10079-4
Medical suction equipment – Part 4: General requirements
This standard specifies general requirements and test methods for medical suction devices. It ensures that these devices are safe and effective.
DIN EN ISO 10555-1
Intravascular catheters - Sterile single-use catheters - Part 1: General requirements
This standard specifies the general requirements for sterile, single-use intravascular catheters. It covers requirements for materials, design, performance, and safety, as well as test methods to ensure the quality and functionality of these medical devices.
DIN EN ISO 10555-3
Intravascular catheters - Sterile single-use catheters - Part 3: Central venous catheters
This standard specifies the requirements for sterile, single-use central venous catheters. It includes requirements for materials, design, performance, and safety, as well as test methods to ensure the quality and functionality of these specialized catheters.
DIN EN ISO 11070
Single-use sterile intravascular insertion instruments, dilators, and guidewires
This standard specifies requirements for sterile, single-use intravascular introductory devices. It covers requirements for materials, design, performance, and safety, as well as test methods to ensure the quality and functionality of these medical devices.
DIN EN ISO 11607-1
Packaging for medical devices to be terminally sterilized – Part 1: Requirements for materials, sterile barrier systems and packaging systems
This standard specifies the requirements for materials, sterile barrier systems, and packaging systems for medical devices that are sterilized in their final packaging. It covers requirements for barrier properties, integrity, and performance of the packaging, as well as test methods to ensure sterility.
DIN EN ISO 11607-2
Packaging for aseptic filling of medical devices - Part 2: Validation requirements for forming, sealing and assembly processes
This standard specifies the validation requirements for the forming, sealing, and assembly processes of medical device packaging. It covers requirements for the validation of these processes, as well as test methods to ensure the integrity and performance of the packaging.
DIN EN ISO 11608-1
Cannula-based injection systems for medical use – Requirements and test methods – Part 1: Cannula-based injection systems
This standard specifies requirements and test methods for needle-based injection systems for medical use. It covers requirements for design, performance, and safety, as well as test methods to ensure the quality and functionality of these systems.
DIN EN ISO 11608-1
Cannula-based injection systems for medical use — Requirements and test methods — Part 1: Cannula-based injection systems
This standard specifies requirements and test methods for needle-based injection systems used in medicine. It covers aspects such as the safety, performance, and compatibility of these systems.
DIN EN ISO 11737-2
Sterilization of health care products – Microbiological methods – Part 2: Sterility testing in the definition, validation and maintenance of a sterilization process
This standard specifies the microbiological methods for testing the sterility of healthcare products. It covers requirements for the definition, validation, and maintenance of sterilization processes, as well as testing procedures to ensure sterility.
DIN EN ISO 11979-4
Ophthalmic Implants - Intraocular Lenses - Part 4: Labeling and Information
This standard specifies the requirements for the labeling and information for ophthalmic implants, particularly intraocular lenses. It covers requirements for marking, documentation, and information for the user, as well as test procedures to ensure the accuracy and completeness of this information.
DIN EN ISO 11979-6
Ophthalmic implants - Intraocular lenses - Part 6: Durability and transportation tests
This standard specifies the requirements for durability and transport testing of ophthalmic implants, particularly intraocular lenses. It covers test methods for assessing the durability and resistance of these implants to transport conditions.
DIN EN ISO 12048
Packaging, Shipping-Ready Packages Compression and Stacking Tests Using a Compression Testing Machine
This standard specifies the requirements and test methods for compression and stacking tests of finished packages ready for shipment. It covers requirements for testing machines, test procedures, and evaluation criteria to ensure the stability and integrity of packaging.
DIN EN ISO 12048
Packaging- Shipping-ready packages- Compression and stacking tests using a compression testing machine
This standard describes a method for determining the stacking strength of packaging to assess its stackability.
DIN EN ISO 13355
Packaging – Shipping-ready packages and loading units – Vibration testing with vertical random excitation
This Standard specifies a procedure for vibration testing of shipping units and load units using random vertical excitation. It is intended to assess the packaging's strength and the protection of the packaged goods during transport.
DIN EN ISO 14937
Sterilization of health care products - General requirements for the characterization of a sterilizing agent and for the development, validation and maintenance of a sterilization process for a medical device
This standard specifies the general requirements for the validation of any sterilization process. It is a general standard to be applied when no specific standard (e.g. for EO or radiation) exists.
DIN EN ISO 14971
Medical devices - Application of risk management to medical devices
This standard establishes a framework for the risk management of medical devices, including the identification, evaluation, and control of risks. It is an essential component of the development and operation of medical devices to ensure safety and effectiveness.
DIN EN ISO 16671
Ophthalmic Implants - Irrigation Solutions for Ophthalmic Surgery
This standard specifies requirements for irrigation solutions used in ophthalmic surgery. It covers the composition, purity, and compatibility of the solutions to ensure safety and efficacy during ophthalmic procedures.
DIN EN ISO 17664-1
Preparation of health care products – Information to be provided by the medical device manufacturer for the reprocessing of medical devices – Part 1: Critical and semi-critical medical devices
This standard defines the information that manufacturers of medical devices must provide to enable the safe and effective reprocessing of critical and semi-critical medical devices. It covers cleaning, disinfection, and sterilization, as well as the documentation of reprocessing processes.
DIN EN ISO 179-1
Plastics – Determination of Charpy impact properties – Part 1: Non-instrumented impact test
This standard describes a method for determining the impact strength of plastics under defined conditions. A pendulum hammer strikes a test specimen, and the absorbed energy is a measure of the material's toughness.
DIN EN ISO 1924-2
Paper and board - Determination of tensile properties - Part 2: Method at constant rate of elongation (20 mm/min)
This standard describes a method for determining the tensile properties of paper and board at a constant rate of elongation. It is used to evaluate the strength and elongation of packaging materials under tensile stress.
DIN EN ISO 1974
Paper - Determination of tearing resistance - Elmendorf method
This standard specifies a method for determining the tear resistance of paper, based on the Elmendorf method. It is used to assess the paper's resistance to tearing, which is crucial for packaging strength.
DIN EN ISO 20417
Medical devices — Information to be supplied by the manufacturer
This standard defines the information that manufacturers of medical devices must provide. This includes technical data, instructions for use, and safety instructions to ensure the safe and effective use of the products.
DIN EN ISO 20695
Enteral Nutrition Systems - Implementation and Testing
This standard specifies requirements for enteral feeding systems, including their design and testing procedures. It covers aspects such as the safety, efficacy, and compatibility of nutrient delivery systems.
DIN EN ISO 20697
Sterile disposable drainage catheters and accessories
This standard specifies requirements for sterile drainage catheters and their accessories intended for single use. It covers aspects such as materials, design, sterilization, and performance characteristics.
DIN EN ISO 2233
Packaging - Shipping-ready packages and load units - Climatic preconditioning for testing
This standard describes procedures for the climatic preconditioning of shipment-ready packages and loading units before testing. It serves to simulate environmental influences in order to evaluate the packaging strength under various climatic conditions.
DIN EN ISO 2234
Shipping-ready packages and load units stacking test under static load
This standard specifies a method for testing the stability of finished packages and unit loads under static load. It is used to assess the stackability and strength of packaging during transport and storage.
DIN EN ISO 22413
Transfer devices for pharmaceutical preparations – Requirements and test methods
This standard specifies requirements for transfer devices for pharmaceutical preparations, including their testing procedures. It covers aspects such as safety, efficacy, and compatibility of devices for administering medications.
DIN EN ISO 2244
Packaging. Ready-to-ship packages and load units. Horizontal impact test (ISO 2244).
This standard describes a method for the horizontal impact test of finished packages and loading units. It is used to assess the resistance of packaging to shocks during transport.
DIN EN ISO 2247
Packaging, Ready-to-ship packages, and loading units Vibration testing with low-frequency and single (ISO 2247)
This standard specifies a method for vibration testing of shipping-ready packages and loading units with low natural frequencies. It is used for evaluating packaging strength and the protection of packaged goods during transport.
DIN EN ISO 2873
Packaging - Ready-to-ship packages and loading units - Vacuum testing (ISO 2873)
Ready-to-ship packages and shipping units
DIN EN ISO 28768
Packaging Ready-to-Ship Packages Overturn test (ISO 8768)
This standard describes a procedure for the topple test of ready-to-ship packages. It is used to assess the stability and strength of packaging against toppling during transport.
DIN EN ISO 3826-1
Plastic bags for human blood and blood components – Part 1: Conventional bags
This standard specifies requirements for plastic bags for human blood and blood components, including their design and performance characteristics. It covers aspects such as materials, design, and safety of the bags.
DIN EN ISO 4180
Packaging, Goods Ready for Dispatch: General Rules for Creating Test Plans
This standard establishes general rules for the creation of test plans for finished packages. It serves as a guide for planning and conducting tests to evaluate packaging strength and the protection of packaged goods.
DIN EN ISO 527-1
Determination of Adhesive Properties – Part 1: General Principles
This standard establishes general principles for the determination of tensile properties of plastics. It includes methods for measuring tensile strength, elongation, and other tensile properties that are crucial for evaluating material performance.
DIN EN ISO 527-3
Plastics – Determination of tensile properties – Part 3: Test conditions for films and sheets
This standard specifies the test conditions for determining the tensile properties of plastic films and sheets. It specifies sample preparation, test speed, temperature, and other conditions to ensure comparable results. Tensile strength is an important parameter for assessing the mechanical properties of plastics.
DIN EN ISO 6270-2
Coatings and varnishes – Determination of resistance to moisture – Part 2: Condensation (Climatic test with heated water reservoir)
This standard describes test methods for determining the moisture resistance of coating materials and varnishes. It includes a condensation test in a climatic cabinet with a heated water reservoir to assess the coating's resistance to moisture.
DIN EN ISO 7864
Sterile hypodermic needles for single use - Requirements and test methods
This standard defines the requirements for sterile single-use injection needles, including material requirements, design criteria, and test methods. It ensures that needles can be used safely and effectively for medical applications. The test methods include tests for sterility, mechanical strength, and compatibility with other medical devices.
DIN EN ISO 7886-1
Sterile single-use syringes for medical purposes - Part 1: Syringes for manual use
This standard specifies the requirements for sterile single-use syringes for manual use. It covers requirements for materials, design, performance, and test methods to ensure the safety and efficacy of the syringes. The test methods include tests for sterility, mechanical strength, and compatibility with other medical devices.
DIN EN ISO 80369-7: 2021
Connectors with small diameter for liquids and gases in medical applications - Part 7: Connectors for intravascular or hypodermic applications
This standard specifies the requirements for connectors for fluids and gases in healthcare, particularly for intravascular or hypodermic applications. It aims to ensure the safety and compatibility of these connectors and to prevent misconnections. The standard covers requirements for design, materials, and test methods.
DIN EN ISO 8318
Packaging - Shipping-ready packages and loading units - Vibration testing with variable sinusoidal frequency
This standard describes two methods for performing a vibration test with sinusoidal vibration and variable frequency on finished packages or unitized loads.
DIN EN ISO 8536-10
Infusion equipment for medical use – Part 10: Accessories for single-use administration sets for pressure infusion
This standard specifies the requirements for disposable accessories for infusion sets used with pressure infusion devices. It covers requirements for materials, design, performance, and test methods to ensure the safety and effectiveness of these devices. Test methods include tests for sterility, mechanical strength, and compatibility with other medical devices.
DIN EN ISO 8536-14
Infusion devices for medical use - Part 14: Clamps and flow regulators for transfusion and infusion equipment without fluid contact
This standard specifies the requirements for clamps and flow regulators for transfusion and infusion devices without liquid contact. It covers requirements for materials, design, performance, and test methods to ensure the safety and efficacy of these devices. The test methods include tests for mechanical strength and compatibility with other medical devices.
DIN EN ISO 8536-2
Infusion devices for medical use – Part 2: Stoppers for infusion bottles
This standard specifies the requirements for stoppers for infusion bottles. It covers requirements for materials, design, performance, and test methods to ensure the safety and efficacy of these devices. Test methods include tests for sterility, mechanical strength, and compatibility with other medical devices.
DIN EN ISO 8536-4
Infusion devices for medical use - Part 4: Infusion sets for single use for gravity infusion
This standard specifies the requirements for disposable gravity infusion sets. It covers requirements for materials, design, performance, and test methods to ensure the safety and effectiveness of these devices. Test methods include tests for sterility, mechanical strength, and compatibility with other medical devices.
DIN EN ISO 8536-8
Infusion devices for medical use – Part 8: Single-use infusion devices with pressure infusion devices
This standard specifies requirements for single-use infusion devices with infusion pumps. It covers requirements for materials, design, performance, and test methods to ensure the safety and effectiveness of these devices. Test methods include tests for sterility, mechanical strength, and compatibility with other medical devices.
DIN EN ISO 8536-9
Infusion devices for medical use – Part 9: Single-use pressure infusion giving sets
This standard specifies the requirements for single-use transfusion lines for pressure infusion devices. It covers requirements for materials, design, performance, and test methods to ensure the safety and effectiveness of these devices. The test methods include tests for sterility, mechanical strength, and compatibility with other medical devices.
DIN EN ISO 9022-2
Optics and optical instruments. Environmental test methods. Part 2: Cold, heat and humidity.
This standard describes environmental testing procedures for optical instruments. It includes tests to determine resistance to climatic conditions and is relevant to the optics industry.
DIN EN ISO 9022-3
Optics and photonics - Environmental test methods - Part 3: Mechanical stress
This standard describes environmental test procedures for optical instruments. It includes tests to determine resistance to mechanical stress and is relevant to the optics industry.
DIN EN ISO 9022-9
Optics and photonics — Environmental testing — Part 9: Solar radiation and weathering
This standard describes environmental test procedures for optical instruments. It includes tests to determine resistance to solar radiation and weathering and is relevant to the optics industry.
DIN EN ISO 9227
Corrosion tests in artificial atmospheres - Salt spray tests
This standard specifies the procedures for salt spray tests to evaluate the corrosion resistance of metals and coated materials. It describes sample preparation, test conditions, and the assessment of corrosion phenomena. This test is important for evaluating the durability and reliability of materials in corrosive environments.
DIN EN ISO 9626
Stainless steel cannulae for the manufacture of medical devices - Requirements and test methods
This standard specifies the requirements for stainless steel cannulae for the manufacture of medical devices. It covers requirements for materials, design, performance, and test methods to ensure the safety and effectiveness of these devices. Test methods include tests for mechanical strength, corrosion resistance, and compatibility with other medical devices.
DIN EN ISO/IEC 17025
General requirements for the competence of testing and calibration laboratories
This standard specifies the general requirements for the competence of testing and calibration laboratories. It covers requirements for the quality management system, technical competence, personnel qualifications, and validation of test methods. The standard aims to ensure the reliability and accuracy of tests and calibrations performed by laboratories.
DIN ISO 11040-4
Pre-filled Syringes – Part 4: Glass Syringe Barrels for Injectable Preparations and Sterilized and Pre-assembled Syringes for Filling
This standard specifies the requirements for prefabricated glass syringe barrels for injectable preparations and for sterilized, preassembled syringes for filling. It includes requirements for materials, design, performance, and test methods to ensure the safety and efficacy of these devices. The test methods include tests for sterility, mechanical strength, and compatibility with other medical devices.
DIN ISO 15759
Medical Infusion Devices - Plastic Caps with Integrated Elastomeric Seal for Containers, Manufactured by the Blow-Fill-Seal (BFS) Process
This standard specifies requirements and test methods for plastic caps with elastomeric seals, which are used for infusion containers manufactured by the BFS process. It ensures that the caps are leak-proof and compatible with medical infusion systems.
ISO 2859-1
Acceptance sampling procedures based on the number of nonconforming items or a defect (attribute sampling) - Part 1: Sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection
This standard describes procedures for acceptance sampling inspection, where the number of defective units or defects in a batch is evaluated. It is based on AQL (Acceptable Quality Level) and helps to ensure product quality.
DIN ISO 4593
Testing of plastic films – Determination of thickness by mechanical probing
This standard specifies a method for determining the thickness of plastic films by mechanical probing. It is important for quality assurance and material testing in film manufacturing.
DIN ISO 8536-7
Infusion devices for medical use – Part 7: Aluminum-plastic combination crimp caps for infusion bottles
This standard specifies requirements and test methods for aluminum-plastic combination pilfer-proof caps used for infusion bottles. It ensures that the caps are leak-proof and secure.
DIN ISO 9022-2
Optics and optical instruments - Environmental test methods - Part 2: Cold, heat and humidity
This standard describes environmental test procedures for optical instruments, particularly concerning cold, heat, and humidity stress. It helps in assessing the reliability and performance of optical devices under various environmental conditions.
DIN ISO 9022-3
Optics and optical instruments - Environmental test methods - Part 3: Mechanical stress
This standard describes test methods for optical instruments subjected to mechanical loads. It helps to assess the robustness and reliability of optical devices under mechanical influences.
DIN ISO 9022-9
Optics and photonics — Environmental testing — Part 9: Solar radiation and weathering
This standard describes test methods for optical and photonic instruments exposed to solar radiation and weathering. It helps to assess the durability and performance of optical devices under these environmental conditions.
DNV-CG-0339
DNV Classification Rules
This DNV (Det Norske Veritas) classification guideline specifies the requirements for environmental testing of equipment used on ships and offshore installations. It covers tests such as vibration, climate, degree of protection, and EMC.
EN ISO 20696
Sterile single-use urethral catheters
This standard specifies requirements and test methods for sterile urethral catheters intended for single use. It ensures that these catheters are safe and effective.
GL Guideline
GL Classification Guideline
This GL Classification Guideline specifies the requirements for environmental testing of equipment intended for use on ships and offshore facilities. It covers tests such as vibration, climatic, degree of protection, and EMC.
GL VI Part 7
Classification and Building Regulations Guidelines for the Performance of Type Approval Tests
This regulation contains classification and construction rules for carrying out type approvals in shipbuilding. It specifies the requirements for the construction and classification of ships.
GMW 3172
Worldwide Engineering Standards – General Specification for Electrical/Electronic Components – Environmental/Endurance
This standard sets general specifications for electrical and electronic components, particularly regarding environmental and durability requirements. It includes tests to evaluate the reliability and resilience of these components under various environmental conditions.
GMW 3172
Worldwide Engineering Standards – General Specification for Electrical/Electronic Components – Environmental/Endurance
This standard sets general specifications for electrical and electronic components, particularly regarding environmental and durability requirements. It includes tests to evaluate the reliability and resilience of these components under various environmental conditions.
Guidelines for Registration and Technical Review of Service Life of Active Medical Devices
Guidelines for the Registration and Technical Review of Active Medical Device Lifespan
These guidelines define the requirements and procedures for the registration and technical review of the service life of active medical devices. They aim to ensure the safety and efficacy of these products throughout their entire service life.
IACS E10
Classification Policy of IACS
This document from the International Association of Classification Societies (IACS) establishes uniform test requirements for the type approval of electrical and electronic equipment used on ships.
IEC 60068-2-6
Environmental tests – Part 2-6: Tests – Test Fc: Vibration (sinusoidal)
This standard describes the execution of vibration tests on products to evaluate their resistance to sinusoidal vibrations. It is part of a series of environmental tests that ensure the reliability of products under various environmental influences.
IEC 60068-2-64
Environmental testing – Part 2-64: Tests – Test Fh: Vibration test (broadband random vibrations and guidance)
This standard describes the execution of vibration tests on products to assess their resistance to broadband random vibrations. It is part of a series of environmental tests that ensure the reliability of products under various environmental influences.
IEC 60068-2-75
Environmental Influences - Part 2 - 75: Tests - Test Eh: Hammer Tests
This standard describes standardized hammer tests for determining the resistance of enclosures to mechanical impacts. The results are classified using the IK code (see also DIN EN 62262).
IEC 60512-16-4
Connectors for electronic equipment - Tests and measurements - Part 16-4: Mechanical tests on contacts and terminals - Test 16d: Tensile strength (crimped connections)
This standard describes the performance of mechanical tests on connectors, especially for assessing the tensile strength of crimped connections. It is part of a series of tests that ensure the reliability and performance of connectors.
IEC 60512-2-1
Connectors for electronic equipment – Tests and measurements – Part 2-1: Electrical continuity tests and contact resistance measurements – Test 2a: Contact resistance – Millivolt-level method
This standard describes the performance of electrical continuity tests and contact resistance measurements on connectors. It is part of a series of tests that ensure the reliability and performance of connectors.
IEC 60512-3-1
Connectors for electronic equipment - Tests and measurements - Part 3-1: Insulation tests - Test 3a: Insulation resistance
This standard describes the performance of insulation tests on connectors, particularly for the evaluation of insulation resistance. It is part of a series of tests that ensure the reliability and performance of connectors.
IEC 60512-4-1
Connectors for electronic equipment - Tests and measurements - Part 4-1: Voltage stress tests - Test 4a: Dielectric strength
This standard describes the performance of voltage stress tests on connectors, specifically for evaluating voltage withstand capability. It is part of a series of tests that ensure the reliability and performance of connectors.
IEC 60512-5-1
Connectors for electronic equipment – Tests and measurements – Part 5-1: Current-carrying capacity tests – Test 5a: Temperature rise
This standard describes the performance of current-carrying capacity tests on connectors, particularly for evaluating temperature rise. It is part of a series of tests ensuring the reliability and performance of connectors.
IEC 60601-1
Medical electrical equipment – Part 1: General requirements for basic safety and essential performance
This standard specifies general requirements for medical electrical equipment, particularly regarding basic safety and essential performance. It covers aspects such as protection against electrical hazards, mechanical strength, and reliability.
IEC 60601-1-11
Medical electrical equipment – Part 1-11: General requirements for basic safety and essential performance – Collateral Standard: Requirements for medical electrical equipment and systems intended for use in the home healthcare environment
This standard specifies particular requirements for medical electrical equipment and systems intended for use in home healthcare. It covers aspects such as usability, safety, and reliability of this equipment in the home environment.
IEC 61215-1
Terrestrial Photovoltaic (PV) Modules - Type Approval and Type Certification - Part 1: Test Requirements
This standard describes the test requirements for terrestrial photovoltaic modules to ensure their design qualification and type approval. It includes tests for evaluating the performance, reliability, and safety of these modules.
IEC 61215-2
Terrestrial Photovoltaic (PV) Modules - Design Qualification and Type Approval - Part 2: Test Procedures
This standard describes the test procedures for terrestrial photovoltaic modules to ensure their design qualification and type approval. It includes detailed instructions for carrying out the tests as defined in Part 1.
IEC 61827
Electrical installations for airfield lighting — Characteristics of in-paved and elevated lights used on aerodromes and helicopter landing areas
This standard describes the properties of lights used for the illumination and marking of aerodromes and helipads. It covers requirements for the performance, safety, and reliability of these lights.
ISO 10993-11
Biological evaluation of medical devices — Part 11: Tests for systemic toxicity
This standard describes the methods for evaluating the systemic toxicity of medical devices. It includes tests to determine the potential harmful effects of medical devices on the entire organism, including acute and chronic toxicity.
ISO 10993-18
Biological evaluation of medical devices – Part 18: Chemical characterization of materials for medical devices in the context of risk management
This standard specifies the procedures for the chemical characterization of materials for medical devices to identify and evaluate potential risks to the patient. It includes methods for the identification and quantification of chemical substances that could be released from the materials.
ISO 11040-4
Pre-filled Syringes - Part 4: Glass Barrels for Injectable Preparations and Sterilized, Prefilled Syringes Ready for Filling
This standard specifies the requirements for glass barrels for pre-filled syringes and sterile pre-filled syringes. It covers requirements for materials, design, manufacturing, and test procedures to ensure the safety and efficacy of the syringes.
ISO 11607-1
Packaging for terminally sterilized medical devices – Part 1: Requirements for materials, sterile barrier systems and packaging systems
This standard specifies the requirements for materials, sterile barrier systems, and packaging systems for terminally sterilized medical devices. It includes requirements for design, manufacturing, and testing methods to ensure the sterility of products during storage and transport.
ISO 11607-2
Packaging for terminally sterilized medical devices – Part 2: Validation requirements for forming, sealing and assembly processes
This standard specifies the validation requirements for the forming, sealing, and assembly processes of packaging systems for terminally sterilized medical devices. It includes procedures for validating these processes to ensure the integrity and effectiveness of the packaging.
ISO 11979-3
Ophthalmic Implants – Intraocular Lenses – Part 3: Mechanical Properties and Test Methods
This standard specifies the mechanical properties and test methods for intraocular lenses. It includes requirements for materials, design, and mechanical tests to ensure the safety and efficacy of the lenses.
ISO 15003
Agricultural machinery — Electrical and electronic equipment — Test for environmental resistance
This standard specifies the test procedures for assessing the resistance of electrical and electronic equipment in agriculture to environmental conditions. It includes tests for temperature, humidity, vibration, and other environmental influences.
ISO 15223-1
Medical devices – Symbols to be used with information to be supplied by the manufacturer
This standard specifies the symbols to be used on medical devices and their packaging to convey important information to the user. It includes requirements for the design, placement, and meaning of the symbols.
ISO 16269-6
Statistical Data Analysis - Part 6: Determining Statistical Tolerance Intervals
This standard describes methods for determining statistical tolerance intervals. It includes procedures for estimating the distribution limits of a population based on sample data.
ISO 16750-1
Road vehicles – Electrical and electronic equipment for vehicles – Environmental conditions and tests – Part 1: General
This standard specifies the general requirements and test procedures for electrical and electronic equipment in road vehicles. It covers tests for various environmental conditions to ensure the reliability and functionality of the equipment.
ISO 16750-3
Road vehicles - Environmental conditions and tests for electrical and electronic equipment - Part 3: Mechanical loads
This standard defines the mechanical tests for electrical and electronic components in road vehicles to simulate the stresses encountered during driving operations.
ISO 16750-3
Road vehicles – Environmental conditions and tests for electrical and electronic equipment – Part 3: Mechanical loads
This standard specifies the mechanical loads that electrical and electronic equipment in road vehicles may be subjected to. It includes tests for vibration, shock, and other mechanical influences to ensure the reliability and functionality of the equipment.
ISO 16750-4
Road vehicles – Environmental conditions and tests for electrical and electronic equipment – Part 4: Climatic loads
This standard defines the climatic stresses to which electrical and electronic equipment in road vehicles can be exposed. It covers tests for temperature, humidity, and other climatic influences to ensure the reliability and functionality of the equipment under various environmental conditions.
ISO 16750-5
Electrical and electronic equipment for motor vehicles - Environmental conditions - Part 5: Chemical loads
This standard defines the chemical stresses to which electrical and electronic equipment in road vehicles may be exposed. It includes tests for chemical influences such as corrosion, oxidation, and other chemical reactions to ensure the reliability and functionality of the equipment.
ISO 187
Paper, board and pulps — Standard atmospheres for conditioning and testing and methods of controlling the atmosphere and conditioning of samples
This standard defines the standard atmosphere for the conditioning and testing of paper, board, and pulps. It specifies how the atmosphere is to be monitored during tests and how samples are to be conditioned to ensure comparable and reproducible test results.
ISO 20653
Road vehicles - Degrees of protection (IP Code) - Protection of electrical equipment against foreign objects, water and access
This standard specifies the degrees of protection (IP code) for electrical devices in road vehicles. It defines protection against the ingress of foreign objects, water, and accidental contact, ensuring the safety and functionality of the devices.
ISO 23908
Protection against injuries from sharp objects - REQUIREMENTS AND TEST METHODS - Protective features for single-use needles, catheter introducers, and blood collection needles
This standard specifies requirements and test methods for safety features against sharps injuries. It applies to single-use needles, catheter insertion devices, and blood collection needles, and defines measures to prevent injuries to medical personnel.
ISO 2669
Environmental tests for aircraft equipment - Endurance acceleration
This standard specifies environmental tests for aircraft equipment, particularly concerning the effects of prolonged acceleration. It defines the test procedures and requirements to ensure the reliability and functionality of equipment under acceleration conditions.
ISO 5636-5
Paper and board — Determination of air permeability (mid range) Part 5: Gurley method
This standard describes the Gurley method for determining the air permeability of paper and board in the medium range. It defines the test methods for measuring air permeability and thus assessing the suitability of the material for various applications.
ISO 6009
Single-use needles for injection purposes - Color coding for identification
This standard specifies the color coding for single-use cannulas to ensure easy identification and prevent mix-ups. It defines the colors for different cannula sizes and types to enhance safety during use.
ISO 7176-11
Wheelchairs — Part 11: Test Dummies
This standard specifies the requirements and test procedures for test dummies used to simulate wheelchair users in tests. It defines the characteristics and dimensions of the dummies to ensure realistic test results.
ISO 7176-22
Wheelchairs — Part 22: Accommodation procedures
This standard describes the procedures for setting up wheelchairs for testing purposes. It specifies how wheelchairs must be correctly prepared and adjusted to achieve comparable and reproducible test results.
ISO 7176-8
Wheelchairs - Part 8: Requirements and test methods for static, impact and fatigue strength
This standard specifies requirements and test methods for the static, impact, and fatigue strength of wheelchairs. It defines the test methods for evaluating the mechanical load capacity and safety of wheelchairs.
ISO 7864
Sterile hypodermic needles for single use - Requirements and test methods
This standard specifies the requirements and test methods for sterile, single-use injection needles. It defines the quality characteristics and test methods to ensure the safety and functionality of the needles.
ISO 7886-1
Sterile single-use syringes for injection purposes - Part 1: Syringes for manual use
This standard specifies the requirements and test procedures for sterile, single-use syringes for manual use. It defines quality characteristics and test methods to ensure the safety and functionality of the syringes.
ISO 80369-20
Connectors with small free passages for medical and pharmaceutical purposes - Part 20: General test methods
This standard specifies general test methods for small-bore connectors in medical applications. It defines methods for evaluating the compatibility, safety, and functionality of these connectors.
ISO 80369-6
Connectors with small internal diameter for liquids and gases in applications for human or animal body examination, perfusion, transfusion, infusion, dialysis, and artificial organs - Part 6: Connectors for neuraxial applications
This standard specifies requirements and test methods for small-diameter connectors used in neuraxial applications. It defines the specific requirements and test methods to ensure the safety and functionality of these connectors.
ISO 80369-7
Connectors with small diameter for liquids and gases in medical applications - Part 7: Connectors for intravascular or hypodermic applications
This standard specifies requirements and test methods for small-bore connectors used in intravascular or hypodermic applications. It defines the specific requirements and test methods to ensure the safety and functionality of these connectors.
ISO 9626
Stainless steel needle tubes for the manufacture of medical devices - Requirements and test methods
This standard specifies requirements and test methods for stainless steel needle tubes used in the manufacture of medical devices. It defines the quality characteristics and testing methods to ensure the safety and functionality of the needle tubes.
ISO/DIS 23417
General specifications and validation procedures for non-sterile packaging of medical devices according to good distribution practice principles
This standard specifies general requirements and validation procedures for non-sterile medical device packaging. It defines methods for ensuring the safety and functionality of this packaging during distribution.
ISTA 1A
Packaged Products Up to 150 lb (68 kg)
This standard defines test methods for packaged products weighing up to 150 lb (68 kg). It covers vibration, shock, and drop tests to ensure packaging integrity during transport.
ISTA 1B
Packaged Products Over 150 lb (68 kg)
This standard applies to packaged products weighing over 150 lb (68 kg). It includes specific tests for heavy packaging, such as vibration, shock, and drop tests, to ensure package integrity during transit.
ISTA 1C
Extended Testing for Packaged Products up to 150 lb (68 kg)
This standard expands the testing for packaged products up to 150 lb (68 kg) and includes additional tests such as climate testing and long-term vibrations to assess packaging durability under various shipping conditions.
ISTA 1D
Extended testing for packaged products over 150 lb (68 kg)
This standard expands the testing for packaged products over 150 lb (68 kg) and includes additional tests such as climatic testing and long-term vibration to test the durability of the packaging under various shipping conditions.
ISTA 1E
Uniformly charged products of the same type
This standard applies to the testing of uniformly loaded products of the same type. It includes tests to ensure that the packaging and cargo securing remain stable during transport.
ISTA 1G
Packaged goods up to 150 lb (68 kg) (Random vibration)
This standard defines test methods for packaged products up to 150 lb (68 kg), with a focus on random vibration testing, to assess the durability of packaging under realistic transport conditions.
ISTA 1H
Packaged Products Over 150 lb (68 kg) (Random Vibration)
This standard applies to packaged products over 150 lb (68 kg) and includes random vibration testing to assess the package's durability under realistic shipping conditions.
ISTA 2A
Packaged Products Up to 150 lb (68 kg)
This standard defines test methods for packaged products weighing up to 150 lb (68 kg). It covers vibration, shock, and drop tests to ensure packaging integrity during transport.
ISTA 2B
Packaged Products Over 150 lb (68 kg)
This standard applies to packaged products weighing over 150 lb (68 kg). It includes specific tests for heavy packaging, such as vibration, shock, and drop tests, to ensure package integrity during transit.
ISTA 2C
Furniture packaging
This standard defines test methods for furniture packaging. It includes tests to ensure that the packaging meets the specific requirements of furniture during transport.
ISTA 3A
Packaged products for parcel shipping up to 70 kg (150 lb)
This standard applies to packaged products shipped via parcel post up to 70 kg (150 lb). It includes specific tests to ensure the durability of the packaging during parcel shipping.
ISTA 3B
Packaged Products for Less Than Truckload (LTL) Transport
This standard defines test procedures for packaged products shipped via Less Than Truckload (LTL) transport. It includes tests to ensure the durability of the packaging during transit.
ISTA 3E
Similar packaged products in uniform loads for truck transport
This standard applies to similar packaged products in uniform loads for truck transport. It includes tests to ensure the durability of packaging and the stability of the load during transport.
ISTA 3F
Packaged products for shipping from distribution center to retail up to 100 lb (45 kg)
This standard applies to packaged products shipped from distribution centers to retail stores, with a weight of up to 100 lb (45 kg). It covers tests to ensure the durability of the packaging during transportation.
ISTA 3H
Products or packaged products in mechanically handled bulk cargo containers
This standard applies to products or packaged products transported in mechanically handled bulk freight containers. It covers tests to ensure the durability of the packaging and the stability of the load during transport.
ISTA 3K
Fast-moving consumer goods in the European retail supply chain
This standard applies to Fast Moving Consumer Goods (FMCG) in the European retail supply chain. It includes tests to ensure packaging durability during transport.
ISTA 3L
General E-commerce Transaction Closing Test
This test standardizes the examination of packaged products for mail order. It includes various stresses that packaging is exposed to during transport, such as shocks, vibrations, and pressure.
ISTA 4AB
Packaged Products for Shipping in Known Distribution Channels
This standard defines tests for packaged products shipped through known distribution channels. It covers tests for mechanical stresses such as drop tests, vibrations, and stacking tests.
ISTA 6-AMAZON.COM - Overboxing
E-commerce fulfillment for package shipping on Amazon.com (over-packaging)
This test is specifically designed for products shipping through Amazon.com. It evaluates the packaging's durability during package shipping, including drops and vibrations.
ISTA 6-AMAZON.COM-SIOC
Ships in Own Container (SIOC) for the Amazon.com Distribution System
This standard applies to products that are shipped in their own packaging (SIOC). It covers testing for the durability of the packaging throughout the Amazon.com distribution system.
ISTA 6-SAMSCLUB
Packaged Products for Shipping in the Sam's Club Distribution System
This standard defines tests for packaged products that are shipped through the Sam's Club distribution system. It includes tests for mechanical stresses such as drop tests and vibrations.
ISTA 7D
Temperature testing for transport packaging
This test checks the resilience of packaging at various temperatures it may be exposed to during transport. It includes tests for extreme heat and cold.
ISTA-6-FedEx-A
Tests for packaged products weighing up to 150 lbs.
This standard defines tests for packaged products weighing up to 150 pounds. It includes tests for mechanical stresses such as drop tests and vibrations.
ISTA-6-FedEx-B
Tests for packaged products weighing over 150 lbs.
This standard defines tests for packaged products weighing more than 150 pounds. It includes tests for mechanical stresses such as drop tests and vibrations.
KTA 3503
Type testing of electrical subassemblies for safety control systems
This standard defines the requirements and test procedures for electrical assemblies in safety control technology. It covers tests for functionality, safety, and reliability.
LN800 Liebherr
Specification for Electronics – General Requirements, Tests & Test Conditions
This specification defines the general requirements and testing procedures for electronic components. It covers tests for functionality, safety, and reliability.
LV 312-1
Hot Water Jet Test (Custom Test Standard)
This test standard defines the requirements and procedures for hot water jet testing of electrical components. It covers tests for watertightness and resistance to hot water.
MBN 50355
Sealing requirement for small parts and fasteners
This standard defines the requirements for the leak-tightness of small parts and connecting elements. It includes tests for leak-tightness and resistance to environmental influences.
MD-PROC-010
Nestlé Nespresso S.A. HQ Lausanne Transport Test Guidelines for Nespresso Accessories
This policy defines the requirements and testing procedures for the transportation of Nespresso accessories. It includes tests for mechanical stresses such as shock and vibration.
MEPC 49/22/Add.2
Revised Guidelines and Specifications for Environmental Protection Equipment for Engine Rooms of Ships Annex Part 3: Specifications for Type Approval Tests for Type Approval of Environmental Protection Equipment
These guidelines define the requirements and procedures for the type approval of environmental protection equipment in ship engine rooms. They include tests for effectiveness and environmental compatibility.
MEPC 58/23
Ballast Water Management System Approval Guidelines
These guidelines define the requirements and procedures for the approval of ballast water management systems. They include testing for efficacy and environmental compatibility.
MIL-DTL-901E
Detail Specification / Shock Tests, H.I. (High-Impact) Shipboard Machinery, Equipment and Systems, Requirements for
This specification defines the requirements and test methods for shock testing of marine machinery, equipment, and systems. It includes tests for high mechanical loads.
MIL-PRF-28800G
Performance Specification - Test Equipment for Use with Electrical and Electronic Equipment
This specification defines the requirements and test procedures for test equipment used with electrical and electronic equipment. It includes tests for functionality and reliability.
MIL-S-901D (NAVY)
Military Specification - Shock Tests, High-Impact (H.I.) Shipboard Machinery, Equipment, and Systems, Requirements for
This military specification defines the requirements and test procedures for shock testing of shipboard machinery, equipment, and systems. It includes tests for high mechanical loads.
MIL-STD-167-1
Mechanical Vibrations for Shipboard Equipment Type I - Environmental and Type II - Internally Excited
This standard specifies the requirements for mechanical vibrations for shipboard equipment. It differentiates between Type I (environmentally induced vibrations) and Type II (internally excited vibrations). The standard is relevant to the maritime industry and ensures that equipment can withstand vibration loads.
MIL-STD-167-1A
Mechanical Vibrations of Shipboard Equipment (Type I - Environmental and Type II - Internally Excited)
This revised standard specifies the requirements for mechanical vibrations in marine equipment. It covers both environmentally induced and internally generated vibrations and is an important standard for the maritime industry.
MIL-STD-202H
DEPARTMENT OF DEFENSE TEST METHOD STANDARD ELECTRONIC AND ELECTRICAL COMPONENTS
This standard defines test methods for electronic and electrical components. It is an important standard for testing components in the electrical industry and ensures that they meet military requirements.
MIL-STD-2073-1E w/CHANGE 2
STANDARD PRACTICE FOR MILITARY PACKAGING
This standard specifies the standard practice for military packaging. It includes requirements for materials, construction, and test methods to ensure that military goods can be safely packed and transported.
MIL-STD-810
Military Standard: Environmental Test Methods for Air and Ground Equipment
This standard covers various environmental tests for military equipment, including high-temperature, low-temperature, humidity, vibration, and shock tests. It is a comprehensive standard for the environmental robustness of equipment.
MIL-STD-810A
Military Standard: Environmental Test Methods for Air and Ground Equipment
This standard covers various environmental tests for military equipment, including high-temperature, low-temperature, humidity, vibration, and shock tests. It is a comprehensive standard for the environmental robustness of equipment.
MIL-STD-810B
Military Standard: Environmental Test Methods for Air and Ground Equipment
This standard covers various environmental tests for military equipment, including high-temperature, low-temperature, humidity, vibration, and shock tests. It is a comprehensive standard for the environmental robustness of equipment.
MIL-STD-810D
Military Standard: Environmental Test Methods for Air and Ground Equipment
This standard covers various environmental tests for military equipment, including high-temperature, low-temperature, humidity, vibration, and shock tests. It is a comprehensive standard for the environmental robustness of equipment.
MIL-STD-810E
Military Standard: Environmental Test Methods for Air and Ground Equipment
This standard covers various environmental tests for military equipment, including high-temperature, low-temperature, humidity, vibration, and shock tests. It is a comprehensive standard for the environmental robustness of equipment.
MIL-STD-810F
Military Standard: Environmental Test Methods for Air and Ground Equipment
This standard covers various environmental tests for military equipment, including high-temperature, low-temperature, humidity, vibration, and shock tests. It is a comprehensive standard for the environmental robustness of equipment.
MIL-STD-810G
Military Standard: Environmental Test Methods for Air and Ground Equipment
This standard covers various environmental tests for military equipment, including high-temperature, low-temperature, humidity, vibration, and shock tests. It is a comprehensive standard for the environmental robustness of equipment.
MIL-STD-810H
Military Standard: Environmental Test Methods for Air and Ground Equipment
This standard covers various environmental tests for military equipment, including high-temperature, low-temperature, humidity, vibration, and shock tests. It is a comprehensive standard for the environmental robustness of equipment.
MIL-STD-810H w/Change 1
Military Standard: Environmental Test Methods for Air and Ground Equipment
This standard covers various environmental tests for military equipment, including high-temperature, low-temperature, humidity, vibration, and shock tests. It is a comprehensive standard for the environmental robustness of equipment.
RMRS Parts I and II: 2012
Rules for technical supervision during the construction of ships and the manufacture of materials and products for ships
This standard specifies the technical requirements and monitoring procedures to be followed during the construction of ships, as well as during the manufacturing of materials and products for ships. It covers aspects such as quality assurance, safety standards, and material testing.
RMRS Parts II and IV: 2007
Rules for technical supervision during the construction of ships and the manufacture of materials and products for ships
This standard specifies the technical requirements and monitoring procedures to be followed during the construction of ships, as well as during the manufacturing of materials and products for ships. It covers aspects such as quality assurance, safety standards, and material testing.
RMRS Parts III and IV: 2012
Rules for technical supervision during the construction of ships and the manufacture of materials and products for ships
This standard specifies the technical requirements and monitoring procedures to be followed during the construction of ships, as well as during the manufacturing of materials and products for ships. It covers aspects such as quality assurance, safety standards, and material testing.
RMRS Parts III and IV: 2011
Rules for technical supervision during the construction of ships and the manufacture of materials and products for ships
This standard specifies the technical requirements and monitoring procedures to be followed during the construction of ships, as well as during the manufacturing of materials and products for ships. It covers aspects such as quality assurance, safety standards, and material testing.
RMRS Part V: 2012
Rules for technical supervision during the construction of ships and the manufacture of materials and products for ships
This standard specifies the technical requirements and monitoring procedures to be followed during the construction of ships, as well as during the manufacturing of materials and products for ships. It covers aspects such as quality assurance, safety standards, and material testing.
RMRS Part XI: 2021
Rules for technical supervision during the construction of ships and the manufacture of materials and products for ships
This standard specifies the technical requirements and monitoring procedures to be followed during the construction of ships, as well as during the manufacturing of materials and products for ships. It covers aspects such as quality assurance, safety standards, and material testing.
RTCA DO-160B
Environmental Conditions and Test Procedures for On-Board Equipment
This standard specifies the environmental conditions to which onboard equipment may be exposed, as well as the corresponding test procedures. It covers tests for temperature, vibration, humidity, and other environmental factors to ensure the reliability of the equipment.
RTCA DO-160C
Environmental conditions and test procedures for onboard equipment (including amendments 1, 2, and 3)
This standard specifies the environmental conditions to which onboard equipment may be exposed, as well as the corresponding test procedures. It covers tests for temperature, vibration, humidity, and other environmental factors to ensure the reliability of the equipment.
RTCA DO-160D
Environmental Conditions and Test Procedures for On-Board Equipment
This standard specifies the environmental conditions to which onboard equipment may be exposed, as well as the corresponding test procedures. It covers tests for temperature, vibration, humidity, and other environmental factors to ensure the reliability of the equipment.
RTCA DO-160D incl. CHANGE NO.1
Environmental Conditions and Test Procedures for On-Board Equipment
This standard specifies the environmental conditions to which onboard equipment may be exposed, as well as the corresponding test procedures. It covers tests for temperature, vibration, humidity, and other environmental factors to ensure the reliability of the equipment.
RTCA DO-160E
Environmental Conditions and Test Procedures for On-Board Equipment
This standard specifies the environmental conditions to which onboard equipment may be exposed, as well as the corresponding test procedures. It covers tests for temperature, vibration, humidity, and other environmental factors to ensure the reliability of the equipment.
RTCA DO-160F
Environmental Conditions and Test Procedures for On-Board Equipment
This standard specifies the environmental conditions to which onboard equipment may be exposed, as well as the corresponding test procedures. It covers tests for temperature, vibration, humidity, and other environmental factors to ensure the reliability of the equipment.
RTCA DO-160G: incl. CHANGE NO.1
Environmental Conditions and Test Procedures for On-Board Equipment
This standard specifies the environmental conditions to which onboard equipment may be exposed, as well as the corresponding test procedures. It covers tests for temperature, vibration, humidity, and other environmental factors to ensure the reliability of the equipment.
Russian River Rules §6 & §7
Russian River Rules §6&§7 2019-01
This standard contains specific rules and regulations for the Russian River, particularly sections §6 and §7. It includes requirements for navigation, safety precautions, and environmental standards.
US Coast Guard 46 CFR Part 162.050-37
Title 46 of the Code of Federal Regulations - Vibration Testing
This standard specifies the requirements and procedures for vibration testing of ships. It ensures that ships comply with the established vibration standards, thereby guaranteeing safety and reliability.
VDA 233-102
Test Sheet for Assessing the Corrosion Behavior of Materials and Components
This standard from the German Association of the Automotive Industry (VDA) describes a specific, cyclic corrosion test that realistically simulates real-world environmental conditions for vehicle components (alternating salt spray, humidity, and dryness).
VDR Part IV
Technical monitoring during product manufacturing
This standard specifies the technical requirements and monitoring procedures to be observed during the manufacturing of products. It covers aspects such as quality assurance, safety standards, and material testing.
VG 95613
Packaging materials — Transport and storage containers, medium-sized, reusable — Technical specification
This standard defines the technical specifications for medium-sized, reusable transport and storage containers. It includes requirements for materials, design, durability, and environmental compatibility.
VG 95614
Packaging materials — Transport and storage containers, small, reusable — Technical specification
This standard defines the technical specifications for small, reusable transport and storage containers. It covers requirements for materials, design, durability, and environmental compatibility.
VW 80000
Electrical and Electronic Components in Motor Vehicles up to 3.5t General Requirements, Test Conditions and Tests
This standard specifies the general requirements, test conditions, and test procedures for electrical and electronic components in vehicles up to 3.5 tons. It includes tests for functionality, safety, and reliability.
VW-PV1200
LV 124 Electrical and Electronic Components in Motor Vehicles up to 3.5 t
This standard specifies the requirements and test procedures for electrical and electronic components in motor vehicles up to 3.5 tons. It covers tests for functionality, safety, and reliability.
VW-PV1209
Corrosion testing (cyclic corrosion test)
This standard defines the requirements and procedures for corrosion testing of motor vehicles. It includes tests that assess resistance to corrosion under various climatic conditions.
VW-PV1210
Body and attachments, corrosion test
This standard specifies the requirements and test methods for corrosion tests on vehicle bodies and attached parts. It includes tests that examine resistance to corrosion under various conditions.